[Rovernet] TC dwell

magnet at ican.net magnet at ican.net
Sun May 22 07:17:14 EDT 2016


AFAIK, with a point gap of .015, the dwell for a 4-cylinder engine 
should be on the order of 54 deg.

Rover to the best of my knowledge did not specify the dwell for the 
2000, but a trawl of the net suggests 54 deg should be about right.

Cheers,

  -- Bill D.



On 22-May-16 2:35 AM, Roger Matheson via Rovernet wrote:
> Hi All,
>
> Does anyone know the dwell angle for the 2000 TC
>
> Cheer Roger in Oz
>
> -----Original Message----- From: Geff McCarthy via Rovernet
> Sent: Sunday, May 22, 2016 3:46 PM
> To: 'Rovernet'
> Cc: Geff McCarthy
> Subject: Re: [Rovernet] is net alive?
>
> Thanks Kent!  I await further good news!
>
> AvMedSafe
> Geoffrey W. McCarthy MD MBA DipAvMed
> 677 NW Melinda Ave Portland OR USA 97210
> 503-241-8468(h) 503-799-3809 (mobile)
>
> -----Original Message-----
> From: Rovernet [mailto:rovernet-bounces at rovernet.org] On Behalf Of 
> Kent Kinard via Rovernet
> Sent: Saturday, May 21, 2016 7:13 PM
> To: Rovernet <rovernet at rovernet.org>
> Cc: Kent Kinard <kkinard at att.net>
> Subject: Re: [Rovernet] is net alive?
>
> Hi Geff,
> I do have a 14CUX system from a Range Rover.  It is currently on a 
> running vehicle which has been run on e0 for the past year and 
> functions perfectly. It will not be cheap.  The vehicle will soon be 
> parted out.
> I may have an Edelbrock carb and manifold for sale within a week but I 
> haven't picked up the car yet.  I will be installing the stock dual 
> Zenith Strombergs on that car.  I will have to look for the locking 
> tabs.  They will be used.
> Roverly,
> Kent K.
>
> Geff McCarthy via Rovernet wrote:
>> Thanks Kent.  I tried to leave a VM for you:  I have finally decided 
>> to move on the SD1, and wonder if you have either an 
>> Edelbrock-manifold-carb, or RR fuel injection that I might buy.  
>> Also, do you have the front caliper locking tabs?
>>
>> AvMedSafe
>> Geoffrey W. McCarthy MD MBA DipAvMed
>> 677 NW Melinda Ave Portland OR USA 97210
>> 503-241-8468(h) 503-799-3809 (mobile)
>>
>> -----Original Message-----
>> From: Rovernet [mailto:rovernet-bounces at rovernet.org] On Behalf Of
>> Kent Kinard via Rovernet
>> Sent: Saturday, May 21, 2016 3:09 PM
>> To: Rovernet <rovernet at rovernet.org>
>> Cc: Kent Kinard <kkinard at att.net>
>> Subject: Re: [Rovernet] is net alive?
>>
>> Hi Geff,
>> I guess everyone is on the road or under a car.  Chris York has asked 
>> me to write an article for the UK Rover P6 Club concerning the use of 
>> American transmissions behind the Rover V8.  When it's done, I will 
>> send it to RCCA and RCCC as well.  Stay tuned.
>> Roverly,
>> Kent K.
>>
>> Geff McCarthy via Rovernet wrote:
>>> I have not received any messages in 3w.
>>>
>>> AvMedSafe
>>> Geoffrey W. McCarthy MD MBA DipAvMed
>>> 677 NW Melinda Ave Portland OR USA 97210
>>> 503-241-8468(h) 503-799-3809 (mobile)
>>>
>>> -----Original Message-----
>>> From: Rovernet [mailto:rovernet-bounces at rovernet.org] On Behalf Of
>>> peter king via Rovernet
>>> Sent: Friday, April 29, 2016 9:53 AM
>>> To: Rovernet <rovernet at rovernet.org>
>>> Cc: peter king <peter at king-co.com>
>>> Subject: Re: [Rovernet] play in 3500s differential
>>>
>>> Hi all,
>>>
>>> Thanks for your thoughts on differential and u-joints. I got 
>>> everything back together last night, and the new half shaft u-joints 
>>> did the trick. Clunk-free!  (and drip-free—at least from the De-dion 
>>> tube, thanks to new seals). Also many thanks for earlier advice on 
>>> the brake failure switch. I rebuilt it and it’s working fine!  Now 
>>> on to the accelerator linkage to see if I can get some of the slop 
>>> out of it.
>>>
>>> Peter
>>>
>>>
>>>
>>>
>>> Peter King + Company
>>> 10 Derby Square
>>> Suite N2
>>> Salem, MA 01970
>>> 617-292-7877 x302
>>> www.king-co.com <http://www.king-co.com/> www.facebook.com/pkingco
>>> <http://www.facebook.com/pkingco>
>>>
>>>
>>>
>>>
>>>
>>> -------------- next part -------------- An HTML attachment was
>>> scrubbed...
>>> URL:
>>> <http://rovernet.org/pipermail/rovernet_rovernet.org/attachments/2016
>>> 0
>>> 429/a5e5f4c4/attachment.html>
>>> _______________________________________________
>>> Rovernet mailing list
>>> Rovernet at rovernet.org
>>> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>>>
>>>
>>> _______________________________________________
>>> Rovernet mailing list
>>> Rovernet at rovernet.org
>>> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>>
>> _______________________________________________
>> Rovernet mailing list
>> Rovernet at rovernet.org
>> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>>
>>
>> _______________________________________________
>> Rovernet mailing list
>> Rovernet at rovernet.org
>> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>
>
> _______________________________________________
> Rovernet mailing list
> Rovernet at rovernet.org
> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>
>
> _______________________________________________
> Rovernet mailing list
> Rovernet at rovernet.org
> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org
>
> _______________________________________________
> Rovernet mailing list
> Rovernet at rovernet.org
> http://rovernet.org/mailman/listinfo/rovernet_rovernet.org




More information about the Rovernet mailing list